Product Category
Contact Info
ZQ451R temperature resistant silicone rubber
Product performance
ZQ451R is a high temperature resistant silicone adhesive sealant, which surpasses ordinary 451 silicone in terms of temperature resistance. Its notable features are: it has good temperature resistance, good electrical insulation, and can be used for a long time in the range of -60~320℃. It also has good adhesion, moisture resistance, shock resistance, corona resistance, leakage resistance and aging resistance. It is widely used for bonding and sealing electronic components with high temperature resistance.
The main purpose
Bonding and sealing of heating pipes, steam irons, high temperature air filters, high temperature ovens and other industrial products; sealing of high temperature pipes.
Technical Parameters
Performance |
ZQ-451R |
|||
Before curing | Exterior | Paste red/black viscous body | Semi-flowing red/black viscous body | Flowing red/black viscous body |
Viscosity(cps) |
-- |
20000~50000 |
3000~10000 |
|
Relative density(g/cm3) |
1.05~1.45 |
1.15~1.35 |
1.05~1.15 |
|
Tack-free time(min) |
10--30 |
10--30 |
10--30 |
|
Full curing time (d) |
3~7 |
3~7 |
3~7 |
|
Curing type | One-component deoxime type | One-component deoxime type | One-component deoxime type | |
solid Transform Rear |
Hardness(Shore A) |
30-50 |
30-50 |
30±5 |
Tensile strength(MPa) |
≥1.5 |
≥1.2 |
≥0.8 |
|
Shear strength(MPa) |
≥1.4 |
≥1.0 |
≥0.6 |
|
Elongation at break(%) |
250~450 |
150~250 |
150~250 |
|
Operating temperature range(℃) |
-60~250 |
-60~250 |
-60~250 |
|
Volume resistivity (Ω·cm) |
≥1.0×1016 |
≥1.0×1016 |
≥1.0×1016 |
|
Dielectric strength (kV/·mm) |
≥19 |
≥19 |
≥19 |
|
Dielectric constant (1.2MHz) |
2.8 |
2.8 |
2.8 |
|
Loss factor(1.2MHz) |
0.001 |
0.001 |
0.001 |
Note: All mechanical and electrical properties are measured after curing for 7 days under the conditions of 25℃ and 55% relative humidity. The performance of each type of silica gel is subject to the actual test report.
Use process and precautions
1. Clean the surface: clean the surface of the adhered or coated object to remove rust, dust, oil and other contaminants.
2. Glue: Unscrew (or cut off) the cap of the hose, squeeze the glue onto the cleaned surface to make it evenly distributed, and close the glued surface to fix it.
3. Solidification: Put the glued or sealed parts in the air and let them solidify naturally. The curing process is a curing process from the surface to the inside. Within 24 hours (room temperature and 55% relative humidity), the glue will be cured to a depth of 2 to 4 mm. If the glue position is deep, especially the parts that are not easily exposed to air, The curing time will be extended. If the temperature is lower, the curing time will also be extended. It takes more than 7 days for the 6mm thick sealant to fully cure.
4. After the operation is completed, the unused glue should be tightened immediately and sealed and stored. When using it again, if there is a little skin on the seal, just remove it, and normal use will not be affected. During the storage of the glue, a small amount of solidification may also occur at the mouth of the tube. After it is removed, it can be used normally without affecting product performance. If you accidentally get into your eyes before curing, seek medical attention.
Viscosity and color
Various viscosity can be adjusted according to customer requirements.
Shelf life
This product is stored in a cool and dry place at 28°C, with a shelf life of 12 months.
Executive standard
Q/320481 MTH002-2012。
Transport
This product is non-dangerous and should be transported in accordance with general conditions.
Packing specification
310ML/piece, 25 pieces/box; 50ML/piece, 200 pieces/box.
Limited liability statement
This product description can never replace the user's necessary test before use. The user's test result is the only guarantee that this product is suitable for its specific application requirements. The company only guarantees that the product meets the factory quality inspection requirements, and does not approve any other forms of guarantee and claim clauses. It is confirmed that it is a quality problem of this product. The company only provides replacement or refund of the sales amount for the defective product, and is not responsible for any indirect or incidental damage.
If you are interested in our products, welcome to leave us a message, we will provide you with satisfactory products and services! !
Related Products
-
Mobile Site