Product Category
Contact Info
ZQ455S Electronic Grade Silicone Rubber
Product performance
ZQ455S is an electronic grade silicone rubber, which cures into an elastomer when wet and at room temperature. Since the use of different curing systems can meet the needs of electronic materials, the volatiles are ester substances during the curing process, which is environmentally friendly and has the advantages of no corrosion to electronic materials. At the same time, it has good resistance to cold and heat alternating properties, aging resistance and electrical insulation properties. Good moisture-proof, anti-shock, corona and anti-leakage performance. It has good resistance to high and low temperature, and the performance does not change much in the range of -50℃~+200℃. It has good adhesion to most electronic plastics and metal materials.
The main purpose
Mainly used for bonding and sealing of various household electronics and electrical appliances; fixing and sealing of electronic components; bonding and sealing of automobiles and LED lamps. It is a general-purpose adhesive for the electronics industry and has a wide range of uses.
Technical Parameters
Performance |
ZQ455 |
|
Before curing | Exterior | Translucent/black/white/gray paste or viscous |
Relative density(g/cm3) |
1.01~1.05 |
|
Tack-free time(min) |
10--60 |
|
Full curing time (d) |
3~7 |
|
Curing type | One-component deketoxime type | |
Solid change Rear |
Hardness(Shore A) |
20~50 |
Tensile strength(MPa) |
1.0-1.8 |
|
Shear strength(MPa) |
1.0-1.6 |
|
Elongation at break(%) |
200--600 |
|
Operating temperature range (℃) |
-60~200 |
|
Volume resistivity (Ω·cm) |
≥≥2×1016 |
|
Dielectric strength (kV/·mm) |
≥20 |
|
Dielectric constant (1.2MHz) |
2.8 |
Note: All mechanical and electrical properties are measured after curing for 7 days under the conditions of 25℃ and 55% relative humidity. The performance of each type of silica gel is subject to the actual test report.
Use process and precautions
1. Clean the surface: clean the surface of the adhered or coated object to remove rust, dust, oil and other contaminants. To
2. Glue: Unscrew (or cut off) the cap of the hose, squeeze the glue onto the cleaned surface to make it evenly distributed, and close the glued surface to fix it. To
3. Solidification: Put the glued or sealed parts in the air and let them solidify naturally. The curing process is a curing process from the surface to the inside. Within 24 hours (room temperature and 55% relative humidity), the glue will be cured to a depth of 2 to 4 mm. If the glue position is deep, especially the parts that are not easily exposed to air, The curing time will be extended. If the temperature is lower, the curing time will also be extended. It takes more than 7 days for the 6mm thick sealant to fully cure. To
4. After the operation is completed, the unused glue should be tightened immediately and sealed and stored. When using it again, if there is a little skin on the seal, just remove it, and normal use will not be affected. During the storage of the glue, a small amount of solidification may also occur at the mouth of the tube. After it is removed, it can be used normally without affecting product performance. If you accidentally get into your eyes before curing, seek medical attention.
Shelf life
This product is stored in a cool and dry place at 28°C, with a shelf life of 12 months.
Executive standard
Q/320481 MTH002-2012
Transport
This product is non-dangerous and should be transported in accordance with general conditions.
Packing specification
310ML/piece, 25 pieces/box; 100ML/piece, 100 pieces/box.
Limited liability statement
This product description can never replace the user's necessary test before use. The user's test result is the only guarantee that this product is suitable for its specific application requirements. The company only guarantees that the product meets the factory quality inspection requirements, and does not approve any other forms of guarantee and claim clauses. It is confirmed that it is a quality problem of this product. The company only provides replacement or refund of the sales amount for the defective product, and is not responsible for any indirect or incidental damage.
If you are interested in our products, welcome to leave us a message, we will provide you with satisfactory products and services! !
Related Products
-
Mobile Site