Language

Product Category

全部产品分类

Contact Info

1/1
Number of views:
1000

ZQ1260R type windshield glue

ZQ1260R modified silane sealant is a product produced with high-quality raw materials and special processing technology. It has a single component, medium and high modulus, moisture-absorbing and curing into an elastomer. It has the advantages of fast deep curing, good aging resistance and high strength. High bonding strength, good aging resistance, solvent-free, friendly to the human body, healthy and environmentally friendly.
Retail price
0.0
Market price
0.0
Number of views:
1000
Quantity
-
+
1
Main Configuration

Product performance

ZQ1260R modified silane sealant is a product produced with high-quality raw materials and special processing technology. It has a single component, medium and high modulus, moisture-absorbing and curing into an elastomer. It has the advantages of fast deep curing, good aging resistance and high strength. High bonding strength, good aging resistance, solvent-free, friendly to the human body, healthy and environmentally friendly. Has the following outstanding advantages:

● Low odor

● No primer can realize bonding to a variety of substrates

● Excellent anti-ultraviolet and anti-aging properties

● No mildew

● Paintable

The main purpose

It is widely used for self-adhesive and mutual adhesion between metals, plastics, glass and other materials, as well as the sealing of gaps and joints. Mainly suitable for bonding and sealing of automobile windshield glass; bonding and sealing of parts such as coaches, trains, heavy truck cabs, ships, containers, elevators, ventilation pipes, and the protection of bridge steel cables.

Technical parameter

Performance

ZQ1260R

solid
change
before
Exterior White/black/grey paste

Relative density(g/cm3)

1.35——1.50

  Tack-free timem

30--60

Full curing time(d)

2---7

Curing type One-component dealcoholization type
solid
change
Rear

HardnessA

45±5

Tensile strength(Mpa)

≥2.5

Shear strengthN/cm

≥2.0

Elongation at break

200——400

Peel strength(N/mm)

>9.5

Operating temperature range

-60℃—100℃

Volume resistivityΩ/cm

≥2.0×1016

Dielectric strength(Kv/mm)

≥18

Dielectric constant(1.2MHz)

2.5

Note: All mechanical and electrical properties are measured after curing for 7 days under the conditions of 25℃ and 55% relative humidity. The performance of each type of silica gel is subject to the actual test report.

Use process and precautions

1. Clean the surface: clean the surface of the adhered or coated object to remove rust, dust, oil and other contaminants.

2. Glue: Unscrew (or cut off) the cap of the hose, squeeze the glue onto the cleaned surface to make it evenly distributed, and close the glued surface to fix it.

3. Solidification: Put the glued or sealed parts in the air and let them solidify naturally. The curing process is a curing process from the surface to the inside. Within 24 hours (room temperature and 55% relative humidity), the glue will be cured to a depth of 2 to 4 mm. If the glue position is deep, especially the parts that are not easily exposed to air, The curing time will be extended. If the temperature is lower, the curing time will be extended. It takes more than 7 days for the 6mm thick sealant to fully cure.

4. After the operation is completed, the unused glue should be tightened immediately and sealed and stored. When using it again, if there is a little skin on the seal, just remove it, and normal use will not be affected. During the storage of the glue, a small amount of solidification may also occur at the mouth of the tube. After it is removed, it can be used normally without affecting product performance. If you accidentally get into your eyes before curing, seek medical attention.

Shelf life

This product is stored in a cool and dry place at 28°C, with a shelf life of 12 months.

Executive standard

Q/320481 MTH002-2012。

Transport

This product is non-dangerous and should be transported in accordance with general conditions.            

Packing specification

310ML/piece, 25 pieces/box.

Limited liability statement

This product description can never replace the user's necessary test before use. The user's test result is the only guarantee that this product is suitable for its specific application requirements. The company only guarantees that the product meets the factory quality inspection requirements, and does not approve any other forms of guarantee and claim clauses. It is confirmed that it is a quality problem of this product. The company only provides replacement or refund of the sales amount for the defective product, and is not responsible for any indirect or incidental damage.

We could not find any corresponding parameters, please add them to the properties table
Prev:
Hot key words

Silica gel

Sealant

Thermal Grease

LED lamp sealant

Window sealant

Electronic potting glue

Stone glue

Flame retardant glue

Anticorrosive coating

Power Coating

Windshield glue

Transparent sealant

If you are interested in our products, welcome to leave us a message, we will provide you with satisfactory products and services! !

Username used for comment:
客户留言
Description:

Related Products

  • Mobile Site Mobile Site
Copyright © 2021 Jiangsu Tomorrow Rubber Industry Co., Ltd.
Powered by www.300.cn This website already supports IPv6