Product Category
Contact Info
ZQ452 T-type silica gel
Product performance
ZQ452 T-type is a general-purpose low viscosity room temperature curing one component silicone potting and batch application adhesive. This product has low viscosity and is easy to apply. It can also be sprayed with solvent dilution equipment. It is easy to use and has good adhesion. Except for slight corrosion to copper, most metals have no corrosion. It has good cold and heat alternating resistance, aging resistance and electrical insulation, good moisture-proof, earthquake resistance, corona resistance and leakage resistance.
Main purpose
This product is suitable for batch application and protection of various electronic circuit boards; Shallow potting of electronic components plays a good role in insulation and waterproof.
Technical parameter
Performance | ZQ452T type | |
Before curing | Exterior | White/black/red/gray/transparent fluid viscous body |
Relative density (g/cm3) |
1.05~1.25 |
|
Viscosity(cps) |
1500--30000 |
|
Tack-free time (min) |
10--60 |
|
Full curing time (d) |
3~5 |
|
Curing type | One-component condensation deketoxime type | |
solid change Rear |
Tensile strength (MPa) |
0.5——1.2 |
Elongation at break(%) |
100--350 |
|
Hardness (Shore A) |
15-25 |
|
Shear strength (MPa) |
0.5——1.0 |
|
Operating temperature range (℃) |
-60~250 |
|
Linear shrinkage (%) |
0.6 |
|
Volume resistivity (Ω·cm) |
1.0×1015 |
|
Dielectric strength (kV/·mm) |
18 |
|
Dielectric constant (1.2MHz) |
2.8 |
|
Loss factor (1.2MHz) |
0.001 |
Note: All mechanical and electrical properties are measured after curing for 7 days under the conditions of 25℃ and 55% relative humidity. The performance of each type of silica gel is subject to the actual test report.
Use process and precautions
1. Clean the surface: clean the surface of the adhered or coated object to remove rust, dust, oil and other pollutants.
2. Apply Glue: unscrew (or cut off) the cap of the rubber hose, squeeze or spray the glue onto the cleaned surface to make it evenly distributed.
3. Solid Plasticization: place the glued parts in the air and let them cure naturally. The curing process is a curing process from the surface to the inside. Within 24 hours (room temperature and 55% relative humidity), the adhesive will be cured to a depth of 2 ~ 4mm. If the sizing position is deep, especially where it is not easy to contact the air, the complete curing time will be extended. If the temperature is low, the curing time will also be extended. It takes more than 7 days for the 6mm thick sealant to be fully cured. It is recommended to use tomorrow's two-component potting adhesive for potting with a thickness of more than 6mm.
4. After the operation, the unused glue shall be immediately tightened and sealed for storage. When used again, if there is a little crust at the seal, it can be removed without affecting the normal use. During the storage of the adhesive, a small amount of curing may occur at the nozzle, which can be used normally after being removed without affecting the product performance. If it accidentally enters the eye before curing, see a doctor.
Viscosity specification
Various viscosity and color specifications can be adjusted according to customer requirements.
Storage period
The product is stored in a cool and dry place at 28 ℃ with a shelf life of 1 year.
Executive standard
Q/320481 MTH002-2012
Transportation
This product is non dangerous and is transported according to general conditions.
Package specification
310ML / piece, 25 pieces / box; 100ml / piece, 100 pieces / box; 1kg / barrel, 10kg / box.
If you are interested in our products, welcome to leave us a message, we will provide you with satisfactory products and services! !
Related Products
-
Mobile Site