Language

Product Category

全部产品分类

Contact Info

1/1
Number of views:
1000

ZQ706 silicone

ZQ706 one-component organic silica gel is a neutral room temperature vulcanized silicone rubber, which cures by absorbing moisture in the air. It is easy to use, safe, and pollution-free. It has excellent aging resistance, moisture resistance, electrical insulation and arc resistance, and can be used for a long time in the temperature range of -60℃-200℃. This product dries quickly, has good adhesion, is non-toxic, non-polluting, non-corrosive, stable in performance, and convenient to use.
Retail price
0.0
Market price
0.0
Number of views:
1000
Quantity
-
+
1
Main Configuration

Product performance
ZQ706 one-component organic silica gel is a neutral room temperature vulcanized silicone rubber, which cures by absorbing moisture in the air. It is easy to use, safe, and pollution-free. It has excellent aging resistance, moisture resistance, electrical insulation and arc resistance, and can be used for a long time in the temperature range of -60℃-200℃. This product dries quickly, has good adhesion, is non-toxic, non-polluting, non-corrosive, stable in performance, and convenient to use.

Main purpose
It is suitable for coating protection of electronic components, all kinds of lamps, meters, electronic modules, stainless steel products, food machinery, medical machinery, medical equipment, refrigerated trucks, steel structure workshops, and bonding reinforcement waterproof and moisture-proof insulation and sealing.

Technical parameter

Performance

ZQ-706

ZQ-706A

ZQ-706B

ZQ-706C

Before curing Exterior Non-flowing translucent viscous body Micro-flowing translucent viscous body Micro-flowing translucent viscous body

Viscosity(cps)

50000~80000

20000~50000

3000~10000

Relative density(g/cm3)

1.05~1.15

1.05~1.15

1.05~1.15

Tack-free time(min)

3--30

3--30

3--30

Full curing time (d)

3~7

3~7

3~7

Curing type One-component dealcoholization type One-component dealcoholization type One-component dealcoholization type
solid
change
Rear

Hardness(Shore A)

40±5

35±5

30±5

Tensile strength(MPa)

≥1.5

≥1.2

≥0.8

Shear strength(MPa)

≥1.5

≥1.2

≥0.8

Elongation at break(%)

200~500

200~500

100~300

Operating temperature range(℃)

-60~200

-60~200

-60~200

Volume resistivity  (Ω·cm)

≥1.0×1016

≥1.0×1016

≥1.0×1016

Dielectric strength (kV/·mm)

≥18

≥18

≥18

Dielectric constant (1.2MHz)

2.8

2.8

2.8

Loss factor(1.2MHz)

0.001

0.001

0.001

Note: All mechanical and electrical properties are tested after curing for 7 days under the conditions of 25℃ and 55% relative humidity. The performance of each type of silica gel is subject to the actual test report.

Use process and precautions

1. Clean the surface: clean the surface of the adhered or coated object to remove rust, dust, oil and other contaminants.

2. Glue: Unscrew (or cut off) the cap of the hose, squeeze the glue onto the cleaned surface to make it evenly distributed, and close the glued surface to fix it.

3. Solidification: Put the glued or sealed parts in the air and let them solidify naturally. The curing process is a curing process from the surface to the inside. Within 24 hours (room temperature and 55% relative humidity), the glue will be cured to a depth of 2 to 4 mm. If the glue position is deep, especially the parts that are not easily exposed to air, The curing time will be extended. If the temperature is lower, the curing time will also be extended. It takes more than 7 days for the 6mm thick sealant to fully cure.

After the operation is completed, the unused glue should be tightened immediately and sealed and stored. When using it again, if there is a little skin on the seal, just remove it, and normal use will not be affected. During the storage of the glue, a small amount of curing may also occur at the mouth of the tube. After it is removed, it can be used normally without affecting product performance. If you accidentally get into your eyes before curing, seek medical attention.

Viscosity and color

Various viscosity and color specifications (white, black, gray, red) can be adjusted according to customer requirements.

Shelf life

 This product is stored in a cool and dry place at 28°C, with a shelf life of 12 months.

Executive standard

Q/320481 MTH002-2012

Transportation

This product is non-dangerous and should be transported in accordance with general conditions.              

Packing specification

300ML/piece, 25 pieces/box; 50ML/piece, 200 pieces/box; 2600ML/piece, 4 pieces/box.

We could not find any corresponding parameters, please add them to the properties table
Hot key words

Silica gel

Sealant

Thermal Grease

LED lamp sealant

Window sealant

Electronic potting glue

Stone glue

Flame retardant glue

Anticorrosive coating

Power Coating

Windshield glue

Transparent sealant

If you are interested in our products, welcome to leave us a message, we will provide you with satisfactory products and services! !

Username used for comment:
客户留言
Description:

Related Products

  • Mobile Site Mobile Site
Copyright © 2021 Jiangsu Tomorrow Rubber Industry Co., Ltd.
Powered by www.300.cn This website already supports IPv6