Product Category
Contact Info
ZQ890 T-type silicone
Product performance
ZQ890 T-type silica gel is a high-strength one-component silicone sealant, cured into an elastomer at room temperature, and has no corrosion to most materials. Has good resistance to cold and heat alternating performance, aging resistance and electrical insulation properties. Outstanding moisture-proof, shock-proof and corona-proof, and anti-leakage performance. It has good resistance to high and low temperature, and has little change in performance in the range of -50°C to 200°C. It has good adhesion to most metals and plastics. It belongs to the oxime type curing and slightly corrodes PC.
The main purpose
This product can be used for bonding various electronic and electrical materials and fixing components. As well as bonding and sealing for general industrial purposes. It is especially suitable for the bonding of parts with higher structural requirements.
Technical parameter
| Performance | ZQ-890 T type | |
|
solid change forward |
Exterior | White/black/translucent paste |
|
Relative density （g/cm3） |
1.05--1.45 |
|
|
Tack-free time m |
5--30 |
|
|
Full curing time （d） |
3---7 |
|
| Curing type | One-component dealcoholization type | |
|
solid change Rear |
Hardness A |
25---50 |
|
Tensile strength （Mpa） |
1.6--2.5 |
|
| Shear strength N/cm |
1.5--2.0 |
|
| Elongation at break% |
100--300 |
|
| Operating temperature range |
-60℃--200℃ |
|
| Volume resistivity Ω/cm |
≥1.0×1015 |
|
| Dielectric strength (Kv/mm) |
≥18 |
|
| Dielectric constant (1.2MHz) |
2.8 |
|
Note: All mechanical and electrical properties are measured after curing for 7 days under the conditions of 25℃ and 55% relative humidity. The performance of each type of silica gel is subject to the actual test report.
Use process and precautions
1. Clean the surface: clean the surface of the insulator, and remove dust and oil.
2. Gluing: Use a spray gun to evenly spray the paint on the surface of the insulator.
3. Solidification: Let it solidify naturally in the air.
The curing process is a curing process from the surface to the inside. Within 24 hours (room temperature and 55% relative humidity), the glue will be cured to a depth of 2 to 4 mm. If the position is deep, especially in parts that are not easily exposed to air, The time to fully cure will be extended, and if the temperature is lower, the curing time will also be extended. Before proceeding with further processing or packaging the bonded parts, it is recommended that the user wait long enough so that the firmness and integrity of the bond will not be affected.
Shelf life
This product is stored in a cool, ventilated and dry place at 25°C, with a shelf life of 12 months.
Executive standard
Q/320481 MTH002-2012.
Transportation
This product is non-dangerous and should be transported in accordance with general conditions.
Packing specification
300ML PE plastic pipe/piece, 25 pieces/box; 2600ML plastic barrel/piece, 4 pieces/box; 25kg/5 gallon drum.
Limited liability statement
This product description can never replace the user's necessary test before use. The user's test result is the only guarantee that this product is suitable for its specific application requirements. The company only guarantees that the product meets the factory quality inspection requirements, and does not approve any other forms of guarantee and claim clauses. It is confirmed that it is a quality problem of this product. The company only provides replacement or refund of the sales amount for the defective product, and is not responsible for any indirect or incidental damage.
If you are interested in our products, welcome to leave us a message, we will provide you with satisfactory products and services! !
Related Products
-
Mobile Site
